Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
en:netzer:dimmer [2011/12/19 12:47] svesch [Dimmer circuit] Fixed link error. |
en:netzer:dimmer [2012/01/25 20:56] svesch Reworked preface |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== 230 V Dimmer ====== | ====== 230 V Dimmer ====== | ||
| + | The Netzer supports the direct connection of phase dimmers. So it is possible to control high voltage loads like bulbs via Ethernet resp. Intranet/Internet. | ||
| + | From **firmware version 1.4 pro**, this feature is supported by Netzer. | ||
| <WRAP center round important 60%> | <WRAP center round important 60%> | ||
| - | |||
| **Be careful when experimenting with 230 V. There is danger to life!** | **Be careful when experimenting with 230 V. There is danger to life!** | ||
| - | |||
| </WRAP> | </WRAP> | ||
| - | + | A phase switching mechanism is described here that is for example built up by a thyristor. For this switching mechanism, the important feature of the thyristor is that in zero crossing it deletes from mains voltage itself, i.e. switches off. | |
| - | + | ||
| - | From **version 1.4 pro**, direct addressing of a reverse phase dimmer is supported by Netzer. | + | |
| - | + | ||
| - | + | ||
| - | + | ||
| - | A reverse phase switching mechanism is described here that is for example built up by a thyristor. For this switching mechanism, the important feature of the thyristor is that in zero crossing it deletes from mains voltage itself, i.e. switches off. | + | |
| - | + | ||
| {{ :phase_control.jpg?nolink& |}} | {{ :phase_control.jpg?nolink& |}} | ||
| - | |||
| - | |||
| The switching mechanism basically consists of zero-crossing detectors and a dimmer circuit. | The switching mechanism basically consists of zero-crossing detectors and a dimmer circuit. | ||
| - | + | {{ :en:netzer:phasecontrol.gif?nolink& | Block diagram phase dimmer}} | |
| - | + | ||
| - | {{ :de:netzer:phasecontrol.gif?nolink& | Block diagram reverse phase dimmer}} | + | |
| - | + | ||
| - | + | ||
| ===== Zero-crossing detector ===== | ===== Zero-crossing detector ===== | ||
| - | |||
| - | |||
| IO0 is used as a zero-crossing detector for the 50\ Hz network frequency. For this purpose, the pin is required to be configured as a digital input with an edge trigger switched on: | IO0 is used as a zero-crossing detector for the 50\ Hz network frequency. For this purpose, the pin is required to be configured as a digital input with an edge trigger switched on: | ||
| + | {{ :en:netzer:phasecontrolio0.gif?nolink& | IO0 setting}} | ||
| - | + | Zero crossings must be captured by an external circuit, creating a homopolar pulse during every zero crossing. For this purpose, for example an AC optocoupler such as SFH620 is suitable. | |
| - | {{ :de:netzer:phasecontrolio0.gif?nolink& | IO0 setting}} | + | |
| - | + | ||
| - | + | ||
| - | + | ||
| - | Zero crossings must be captured by an external circuit, creating a homopolar pulse during every zero crossing. For this purpose, for example an AC optocoupler such as | + | |
| - | SFH620 is suitable. | + | |
| - | + | ||
| - | + | ||
| ===== Dimmer circuit ===== | ===== Dimmer circuit ===== | ||
| - | + | A triggered pulse output of Netzer is dimmed. **IO3** or **SPI_INT** are both suitable for this. It is hence possible to operate up to two dimmers in parallel. | |
| - | + | ||
| - | A triggered pulse output of Netzer is dimmed. **IO3** or **SPI_INT** are both suitable for this. It is hence possible to operate up to two dimmers in parallel. | + | |
| - | + | ||
| {{ :en:netzer:phasecontrolpulsee.gif?nolink& | Pulse setting}} | {{ :en:netzer:phasecontrolpulsee.gif?nolink& | Pulse setting}} | ||
| + | This setting allows very granular gradations with a resolution of 200\ ns. Since under mains voltage a half cycle is 10\ ms and values between 100 (the is the smallest possible value in [[en:netzer:io#impuls|pulse operation]] and 50000 possible. Values comply with the time according **to which** the thyristor is powered. I.e. the larger the value, the less power will run at the output. | ||
| - | |||
| - | This setting allows very granular gradations with a resolution of 200\ ns. Since under mains voltage a half cycle is 10 ms and values between 100 (the is the smallest possible value in [[en:netzer:io#impuls|pulse operation]] and 50000 possible. Vlaues comply with the time according **to which** the thyristor is powered. I.e. the larger the value, the less power will run at the output. | ||
